dbba662c

7.4.7. Removal and installation of a starter

Самоконтрящийся fixture is subject to replacement without fail!

Petrol models

463.250 (M112)

Details of installation of a starter on models 463.250 (M112) (1 of 2)

1 — Screws
2 — the Line of a contour 30
3 — the Line of a contour 50

4, 5 — Nuts
M1 — the Starter

Details of installation of a starter on models 463.250 (M112) (2 of 2)

6 — the Air cleaner
7 — the cooling system Fan
8, 14 — Arms
9 — the ATF Line
10 — the GUR Returnable line

11 — the Left guard
12 — the Right guard
13 — the Right support of a suspension bracket of the power unit

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Remove the air cleaner (6) (see the Head of the Power supply system and production of the fulfilled gases).
  3. Remove assembly of the fan of the cooling system with the viscous coupling (7) (see the Head of the Cooling system, heating, ventilation and air conditioning).
  4. Otboltite from a frame the right and left support of the power unit.
  5. Otboltite an arm (8) of fastening of the ATF (9) lines on the right and at the left below and above on the case pallet.
  6. Disconnect the line (10) of the steering pump, - at once to a zakuporta open nipple connections.
  7. Release from a clamp an electrical wiring and an otboltita from a frame the left guard (11).
  8. Otboltite from a frame the right guard (12).
  9. Hang out the engine from above and, having slightly taken it aside in case of need, remove a guard (12).
  10. Otboltite also remove the right support of a suspension bracket of the power unit (13) (see the Head Dvigatel).
  11. Otboltite an arm (14) also disconnect an electrical wiring of contours 30 and 50 (2 and 3).
  12. Turn out screws (1) and remove a starter (M1).
  13. Installation is made upside-down, - track that when lowering the power unit guards were not jammed (11 and 12).
  14. In conclusion make cleaning of the processor memory of system of onboard self-diagnostics (see the Section the General information).

463.246/249 (M113)

Details of installation of a starter on models 463.246/249 (M113) are similar shown on an illustration of the Detail of installation of a starter on models 463.250 (M112) (1 of 2).

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Disconnect an electrical wiring of contours 30 and 50 (2 and 3).
  3. Turn out fixing screws (1) and remove a starter (M1).
  4. Installation is made upside-down.
  5. In conclusion make cleaning of the processor memory of system of onboard self-diagnostics (see the Section the General information).

Diesel models

463.323 (M612)

Details of installation of a starter on models 463.323 (M612)

1 — the Boot
2 — the Clamp
3 — the Electrical wiring of a contour 30

4 — the Electrical wiring of a contour 50
5 — Bolts
M1 — the Starter

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. The car also establish to Poddomkratta it on props.
  4. Remove the left forward wheel.
  5. Remove the left forward bryzgootboynik.
  6. Remove a boot (1).
  7. Otboltite a clamp (2), remove a binding and take aside an electrical wiring plait.
  8. Uncover and disconnect an electrical wiring (3) contours 30.
  9. Disconnect an electrical wiring of a contour 50 (4).
  10. Turn out fixing bolts (5) and through a wheel arch take a starter (M1).
  11. Installation is made upside-down.
  12. In conclusion deactivate the service mode of the TELE AID system, make cleaning of the processor memory of system of onboard self-diagnostics (see the Section the General information).

463.333 (M628)

Details of installation of a starter on models 463.333 (M628)

1 — the Screw
2 — the Right lower air duct
3, 4 — Nuts
5 — the Electrical wiring of a contour 30
6 — the Electrical wiring of a contour 50

7, 8, 11 — Bolts
9, 10, 12 — Support of a suspension bracket of the power unit
M1 — the Starter

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery, - in order to avoid risk of short circuit do not connect the auxiliary accumulator.
  2. The car also establish to Poddomkratta it on props.
  3. Remove the air cleaner (see the Head of the Power supply system and production of the fulfilled gases).
  4. Remove protection of a case.
  5. Disconnect the right lower air duct (2) (see the Head of the Power supply system and production of the fulfilled gases).
  6. Having released nuts (3 and 4), disconnect an electrical wiring of contours 30 and 50 (5 and 6).
  7. Hang out the engine from above.
  8. Having turned out bolts (7 and 8), weaken landing of forward support of a suspension bracket of the power unit (9 and 10).
  9. Having given bolts (11), weaken landing of a back support (12).
  10. Raise the unit, having released forward support and shift it back so that the support (10) got on an emphasis.
  11. Turn out fixing bolts (1) and remove a starter (M1).
  12. Installation is made upside-down.
  13. In conclusion make cleaning of the processor memory of system of onboard self-diagnostics (see the Section the General information).