dbba662c

2.4. Devices of ensuring comfort

The automated air conditioning system (Termatic)

The control panel of functioning of the automated K/V system

The design of the control panel of the K/V system is presented on an illustration.

Control panel of functioning of the Termatic system

1 — the Rotary regulator of installation of the high-speed mode of functioning the Termatic system fan/switch
2 — the Rotary regulator of the choice of temperature condition in the left part of salon
3 — the Rotary regulator of the choice of temperature condition in the right part of salon
4 — the Rotary regulator of the choice of the direction of distribution of air
5 — the Button of activation of an electrical heating of back glass

6 — the Button of inclusion of economy mode
7 — Buttons of inclusion of the AUTO mode
8 — the air circulation mode Switch
9 — the Button of activation of the mode of removal of condensate from glasses

Activation/deactivation of the Termatic system

For activation of system it is necessary to bring the rotary regulator of the choice of the high-speed mode of the fan out of situation 0. Return of the regulator to zero situation allows to disconnect system.

At the disconnected system the supply and circulation of saloon air also stop that can lead to bystry fogging of glasses, - try not to disconnect when using the car system for a long time!

Mode of automatic functioning

The AUTO mode when the choice of intensity and the direction of distribution of air is carried out by system automatically proceeding from the temperature installations set by the user, is basic. For activation of the mode press the AUTO button on the control panel, - the control light-emitting diode which is built in the button has to light up. The choice of the required temperature condition in the right or left part of salon is carried out by rotation of the corresponding rotary regulator, - try to make correction of temperature conditions small steps.

Activation of an electrical heating of back glass can be made in case of need manually.

Manual adjustment of intensity and directions of distribution of air

Intensity and the direction of distribution of air can be exposed manually by means of side rotary regulators on the control panel after preliminary shutdown of the automatic mode from the corresponding button, - the built-in control light-emitting diode of the AUTO mode has to go out, - the chosen earlier temperature installations will change.

Intensity of air supply can change within 5 steps of the high-speed modes of functioning of the fan.

At installation of intensity of air supply on zero shutdown of the Termatic system is made! The choice of this installation has to be made only for a short time.

The choice of the direction of distribution of air provides the following possible options:

— Air supply on having blown wind and side glasses

— Air supply on having blown in glasses, on front level and in foot wells

— Air supply in lobbies and back foot wells

— Air supply on front level

Return to the automatic mode can be made by repeated pressing the AUTO button, - make sure of serviceability of activation of a control light-emitting diode.

The mode of removal of condensate from glasses

For bystry removal of condensate from glasses press the button, - the control light-emitting diode which is built in in the button has to light up. At the same time the system automatically provides transfer to the maximum productivity of a heater and the fan, and all stream of the air given to salon is redirected on having blown wind and side glasses with shutdown of its giving in a back part of salon. At the corresponding complete set the windshield electrical heating is automatically activated. Adjustment of all other installations, except for function of an electrical heating of back glass, for the period of activation of the mode is blocked.

The heating element of heating of a windshield consumes a lot of electric power therefore it is not necessary to activate it for a long time, - shutdown of heating on the timer is not provided!

For shutdown of the mode rather repeatedly to press the same button, or the AUTO button.

For removal of condensate from an external surface of a windshield it is necessary to choose the air supply mode on having blown in glasses () and to activate screen wipers.

Air circulation mode

Activation of the mode of air circulation is made by means of the button on the K/V control panel, - the control light-emitting diode which is built in the button has to light up. In this mode shutdown of giving in salon of fresh air is made that allows to prevent penetration into salon of exhaust gases and unpleasant smells.

Long use of the mode of circulation, leads to fogging of glasses and increase in a spertost of air therefore it is recommended to activate this mode only in case of the valid need and for rather short time, for example, at the movement on the area with the smoke-filled or gas-polluted atmosphere. As soon as need of isolation of salon disappears, supply of fresh air has to be resumed.

Repeated pressing the button of the switch allows to restore air supply.

Also automatic shutdown of the mode of circulation on a timer signal is provided: approximately in 30 minutes at a temperature of external air from 5 °C and above, or in 5 minutes at a temperature of external air below 5 °C. Five-minute installation is activated also at the chosen economy mode of functioning of system (see below).

At high temperatures of external air 30-minute activation of the mode of circulation can automatically be made and is not followed by inclusion of a control light-emitting diode of the push-button switch.

Economy mode

At the choice of economy mode shutdown of the К/В compressor is made.

For activation of the mode press the ACoff/REST button on the control panel, - the control light-emitting diode which is built in in the button has to light up.

On models of the corresponding complete set also automatic shutdown of an additional heater is made.

In economy mode such functions of the Termatic system as cooling and drainage of air are turned off.

Shutdown of the mode is made by repeated pressing of the same button.

Mode of use of residual heat of the engine

Heating of salon can be made during even some time after an engine stop due to use of the power unit of residual heat accumulated by weight. Activation of the mode is made by means of the ACoff/REST button on the control panel, - the control light-emitting diode which is built in the button has to light up.

Before inclusion of the mode of use of residual heat of the engine (REST) turn a key in the ignition lock in situation 1.

At the activated mode adjustment of intensity and the directions of air supply is made automatically (the minimum high-speed mode of the fan usually is chosen). Duration of functioning of system depends on the chosen temperature installations and reference temperature of cooling liquid of the engine.

Necessary condition of use of the REST mode is the sufficient level of a charge of the rechargeable battery.

Switching off of the mode is made automatically on a timer signal approximately in 30 minutes, when turning a key in the ignition lock in situation 2, and also at noticeable decrease in level of a charge of the rechargeable battery.

Heating of back glass

Heating of back glass functions only in situation 2 keys in the ignition lock. Activation of a heating element of back glass is made by means of the corresponding button on the system control panel, - the control light-emitting diode which is built in the button has to light up.

In winter season before inclusion of heating remove with frost and snow flew down.

The heating element of heating of back glass consumes a lot of electric power therefore it is not necessary to activate it for a long time.

Automatic shutdown of heating is made on a timer signal approximately in 6-17 minutes, depending on temperature of external air and speed of the movement of the car.

Shutdown of heating of back glass can happen also at simultaneous activation of a large number of consumers of the electric power, and also at noticeable decrease in level of a charge of the rechargeable battery, - the control light-emitting diode which is built in the button will begin to blink. With restoration of level of tension the heating element is activated automatically.