dbba662c

13.4.2. Removal and installation of activators of the uniform lock

Activators of locks of forward doors

Details of installation of the activator of the lock of a forward door (1 of 3)

Details of installation of the activator of the lock of a forward door (2 of 3)

4 — Driving draft

Details of installation of the activator of the lock of a forward door (3 of 3)

6 — the Driving electric motor


 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Remove the panel of an internal upholstery of a door (see the Head Kuzov).
  3. Disunite the socket of an electrical wiring (shooter) of the activator of the door lock.
  4. Disconnect driving draft from the door lock.
  5. Turn out fixing screws and remove assembly of an executive electric motor (6).
  6. Installation is made upside-down, - track correctness of laying of an electrical wiring and reliability of fixing of the socket.

Activators of locks of back doors

Station wagon models

Details of installation of the activator of the lock of a back door (Station wagon model)

1 — the electrical wiring Socket

2 — the Driving electric motor

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the panel of an internal upholstery of a door (see the Head Kuzov).
  4. Release a plait of an electrical wiring of the uniform lock from door assembly and disunite the socket (1).
  5. Disconnect driving draft (shooter) from the door lock.
  6. Release fixture and remove a driving electric motor (2).
  7. Installation is made upside-down, - track correctness of laying of an electrical wiring and reliability of fixing of the socket.
  8. On models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  9. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine) and perform procedures of basic programming.

Models with wheel base of 2850 mm

Details of installation of the activator of the lock of a back door (model with base of 2850 mm)

3 — the electrical wiring Socket
5 — Driving draft

6 — the Driving electric motor

The order of implementation of the procedure is similar described above for the activator of a forward door (see paragraphs with 1 on 6).

Activator of the lock of a folding board (Cabriolet model)

Details of installation of the activator of the lock of a folding board on the Cabriolet models (1 of 2)

1 — the Plastic tray
2 — the Plastic clamp

3 — the Pin dilator

Details of installation of the activator of the lock of a folding board on the Cabriolet models (2 of 2)

4, 5 — Screws
6 — the Assembly bracket

7 — Driving draft
M14/7 — the Driving electric motor

 PERFORMANCE ORDER

  1. Cast away a back board and uncover a tool compartment its back party.
  2. Having hooked clamps (2), take broad pins (3) and remove a plastic tray of a tool compartment.
  3. Disconnect an electrical wiring from a driving electric motor (M14/7) of the uniform lock.
  4. Separate driving draft from an electric motor (M14/7), - draft remains connected to castle assembly.
  5. Turn out fixing screws (5) and remove from assembly of an electric motor (M14/7) an assembly bracket (6).
  6. Remove an electric motor (M14/7).
  7. Installation is made upside-down.

Activator of the lock of a cover of the hatch of a jellied mouth of the fuel tank

Details of installation of the activator of the lock of a cover of the hatch of a jellied mouth of the fuel tank

1, 2 — Screws
3 — the Lock finger

M14/10 — the Driving electric motor

 PERFORMANCE ORDER

  1. Remove the right back section of side finishing of salon (see the Head Kuzov).
  2. On the Station wagon models turn out the screw (1) of a tension tape of emergency opening of the hatch of a jellied mouth.
  3. Turn out screws (2), previously having marked provisions of their heads in oval openings.
  4. Release from a guide a lock finger (3).
  5. Having inclined back, remove a driving electric motor (M14/10).
  6. On the Cabriolet models disconnect draft of an emergency otpuskaniye of the lock from a lock finger (3).
  7. Disconnect an electrical wiring from the motor (M14/10).
  8. Installation is made upside-down, - track correctness of combination of the tags put in the course of dismantle (see paragraph 2).