dbba662c

13.2.3. Removal and installation of modules of management

General information

The scheme of an arrangement of modules of management onboard the car

A2/5 — the Antenna divider
A2/6 — a CD changer
A2/22 — the Antenna
A2/42 — the TV tuner
A2/65 — the Antenna amplifier
A35/8 — the Module of management of system of an emergency call (E-call) of TELE AID
A35/11 — the Module of management of the Linguatronic system
B33 — the Sensor of an inclination of anticreeping system (ATA)
B66 — the Conical sensor of an inclination
N2/2 — the Module of management of SRS
N3/10 — the Module of management of ME-SFI injection
N10/1 — the Right module of management of SAM/assembly the block
N10/2 — the Back module of management of SAM/assembly the block

N15/3 — the Module of management of AT (TCM/ETC)
N15/5 — the Selector module (ESM) of AT
N15/7 — the Module of management of the VGS transfer case
N25/6 — the Module of management of heating of back seats
N27 — the Module of management of the sensor of protection against towage
N28/1 — the Module of management of system of registration of connection of the trailer
N39/2 — the Module of management of injection CDI
N47-7 — the Module of management of ABS
N62 — the Module of management of system of the help at the movement by a backing (BA)
X4/30 — the Terminal block (a contour 30, the engine)
Y58/1 — the Valve of a purge of a coal adsorber

The description of procedures of removal and installation of modules of management of injection (ME-SFI/CDI), AT (TCM/ETC), the transfer case, brake and auxiliary stabilization systems (ABS/BAS/EBV/ESP) is provided in the corresponding Heads of the Management (see Chapters of the Power supply system and production of the fulfilled gases, Automatic transmission, the Transmission line and the Suspension bracket and steering).

The module of management of the COMAND system with the multipurpose display (ET4 code)

Details of installation of the module of management of COMAND with the multipurpose display (1 of 2)

1 — the Bolt
A40/3 — the Module of management of teams with the multipurpose display

Details of installation of the module of management of COMAND with the multipurpose display (2 of 2)

1 — the Socket of a signal of the RGB TV tuner
2 — I Will corrode CAN tires (to a combination of devices)
And — I Will corrode giving of food
In — the loudspeaker Socket
D2B — the Socket of the fiber-optical tire

D — the Socket of an entrance signal of the FM/AM antenna
Е — the Socket of an entrance signal of GPS
F — the Socket of an output signal of IF *
S — the Safety lock

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove facing of the central section of the dashboard (see Removal and installation of the facing panel of console section of the dashboard).
  4. Turn out fixing bolts (1) and release assembly of the module of management / the multipurpose display (A40/3) from the dashboard.
  5. Disunite electric sockets (1, 2, A, V, D, E, F).
  6. Accurately, trying not to extend and not to break a cable, disunite the D2B socket of the fiber-optical tire.
  7. Installation is made upside-down, - at the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  8. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Modules of management of door assemblies

Forward door

Details of installation of the module of management of a forward door

In — Fixing screws
With — Bindings

N69/1 — the Module of management of the left door
N69/2 — the Module of management of the right door

 PERFORMANCE ORDER

  1. Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — Grounding of the battery
  1. Remove the panel of an internal upholstery of a door (see the Head Kuzov).
  2. Disconnect an electrical wiring from the door module of management (N69/1 or N69/2) (see the Section Detachment and connection of an electrical wiring of assembly blocks and modules of management).
  3. Turn out fixing screws (V) and remove the module of management (N69/1 or N69/2).
  4. Installation is made upside-down, - an electrical wiring of modules, having tracked that wires did not cross, fix by new bandages (C).
  5. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Back door

Details of installation of the module of management of a back door (1 of 2)

1 — Clamps
2 — Latches
3 — the upholstery Panel

N69/3 — the Module of management of the left door
N69/4 — the Module of management of the right door

Details of installation of the module of management of a back door (2 of 2)

And — the Binding


 PERFORMANCE ORDER

  1. Turn on the auxiliary accumulator and connect it to the regular battery then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — Grounding of the battery

  1. Remove the panel of an internal upholstery of a door (3) (see the Head Kuzov).
  2. Disconnect an electrical wiring from the door module of management (N69/3 or N69/4) (see the Section Detachment and connection of an electrical wiring of assembly blocks and modules of management).
  3. Having squeezed clamps (1), remove the module of management (N69/3 or N69/4).
  4. Installation is made upside-down, - an electrical wiring of modules, having tracked that wires did not cross, fix by a new binding (And).
  5. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Modules of management of system of activation and perception of a signal (SAM)/assembly blocks of safety locks and relay

Forward module

Details of installation of the forward SAM/assembly module of the block of safety locks and relay

1, 2 — Nuts
3, 4 — SAM electrical wiring Socket

N10/1 — the Forward module of management of SAM

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the main ware box (see the Head Kuzov).
  4. Remove the right lower cover of the dashboard (see the Head Kuzov).
  5. Give fixing nuts (1 and 2) and remove the forward SAM/assembly module the block (N10/1).
  6. Previously having marked, disunite sockets (3 and 4) of the module of management (N10/1) (see the Section Detachment and connection of an electrical wiring of assembly blocks and modules of management).
  7. Installation is made upside-down, - track correctness of laying of an electrical wiring and reliability of fixing of its sockets (see the Section Detachment and connection of an electrical wiring of assembly blocks and modules of management).
  8. On models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  9. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine) and enter the required basic settings of the onboard equipment.

Back module

Details of installation of the back SAM/assembly module of the block of safety locks and relay (N10/2)

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the central console (see the Head Kuzov) and the air duct laid under it.
  4. Turn out fixing screws and remove the SAM/assembly module the block (N10/2).
  5. Installation is made upside-down, - track correctness of laying of an electrical wiring and reliability of fixing of its sockets (see the Section Detachment and connection of an electrical wiring of assembly blocks and modules of management).
  6. On models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  7. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine) and enter the required basic settings of the onboard equipment.

Module of management of the electronic switch of ignition (EIS/EZS)

Details of installation of the module of management of EIS/EZS

1 — Clamps
2 — the Driving cable of the lock of ignition

3 — the electrical wiring Socket
N73 — the Module of management EIS/EZS

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  1. Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — Grounding of the battery

  1. Take the ignition key.
  2. Remove the left lower section of finishing of the dashboard (see the Head Kuzov).
  3. Squeeze clamps (1) and disconnect a driving cable (2) from the EIS (N73) module, having pulled it in the direction specified by an arrow.
  4. Disunite the socket (3) electrical wirings of the EIS (N73) module.
  5. Installation is made upside-down, - the replaceable EIS module has to be programmed according to the instructions enclosed in a set.
  6. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Module of management of telecommunications (ET7/EV7 codes)

Details of installation of the module of management of telecommunications (ET7/EV7 codes)

1 — the module Console
And — I Will corrode connections of a fiber-optical cable

In — the Socket
N112 — the Module of management

 PERFORMANCE ORDER

  1. Remove the central console (see the Head Kuzov).
  2. Disunite the socket (A) of connection of a fiber-optical cable on the module of management (N112), - at once close sockets of wave guides protective caps.
  3. Having squeezed lock uvulas and having accurately pulled, disunite the socket(s).
  4. Turn out 2 fixing screws and having released one nut, remove the console (1) of the module of management (N112) from the tunnel of the transmission line.
  5. Turn out two fixing screws located from below and remove the module of management (N112) from the console panel (1).
  6. Installation is made upside-down.
  7. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Module of management of system of an emergency call of TELE AID (ET2 code)

Model 463.250/323/333

Details of installation of the module of management of system of an emergency call of TELE AID on models 463.250/323/333

1 — Screws
2 — electrical wiring Sockets

A35/8 — the Module of management
Arrow — the electrical wiring Socket

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the central console (see the Head Kuzov).
  4. Remove the module of management of AT (ECM/ETC) (see the Head Automatic transmission).
  5. Turn out three fixing screws (1), disunite two sockets (2), then disunite the socket shown by an arrow and remove the module of management (A35/8).
  6. Replace the independent battery of food of system of an emergency call.
  7. Installation is made upside-down.
  8. On models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  9. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine) and enter the required basic settings of the onboard equipment.

Model 463.246/249

Details of installation of the module of management of system of an emergency call of TELE AID on models 463.246/249 (1 of 3)

1 — the Cover of the module of management
3 — the Fixing nut
A35/8 — the Module of management
A35/8j10 — the electrical wiring Socket

In — the Socket of an electrical wiring of the tire of data of CAN
With — the Socket of an antenna cable
Arrow — Clamps

Details of installation of the module of management of system of an emergency call of TELE AID on models 463.246/249 (2 of 3)

4 — the Fixing nut
5 — the module Console

6 — Fixing nuts

Details of installation of the console of the module of management of system of an emergency call of TELE AID on models 463.246/249 (3 of 3)

5 — the module Console
7 — Fixing nuts

8 — the Wire of the tire of data of CAN
9 — Porous insulating material

 PERFORMANCE ORDER

  1. Lift the right front seat and shift it back against the stop.
  2. Release two clamps (2) fastenings of the forward party of a cover (1) of the module of management.
  3. Shift the lifted seat against the stop forward, release two back clamps (arrow) and uncover (1).
  4. Give two nuts (3) fastenings of a back part of the module of management (A35/8).
  5. Again take away the lifted seat in extreme back situation, give two forward nuts (4) and remove the module (A35/8).
  1. Switch off ignition, activate the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — Grounding of the battery

  1. Remove the module of management (A35/8) from a basic arm.
  2. Unblock and disunite the socket (A35/8j10).
  3. Disconnect a fiber-optical cable of the tire of data of CAN and at once muffle both halves of its socket (V) the special, preventing light influence, protective caps.
  4. Disunite the socket (C) an antenna cable.
  5. Remove the module of management of system of an emergency call of TELE AID (A35/8).
  6. In case of need release lobbies (6) and back (7) nuts, separate a wire (8) of the tire of CAN from the console (5), exempt from penoizolyatsionny material (9) and disunite contact sockets, - take care of protection of a fiber-optical wave guide special caps and remove the console (5) of the module, passing an electrical wiring throughout windows through passage.
  7. Installation is made upside-down.
  8. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine) and enter the required basic settings of the onboard equipment.

Module of management of the sensor of protection against towage

Details of installation of the module of management (N27) of the sensor of protection against towage

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the central console (see the Head Kuzov).
  4. Remove the back SAM (N10/2) module, - see above.
  5. Disconnect an electrical wiring from the module of management (N27) of the sensor of protection against towage.
  6. Release fixture and remove the module (N27).
  7. Installation is made upside-down, - on models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  8. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine) and enter the required basic settings of the onboard equipment.

The module of management of the ultrasonic device of the help at the movement by a backing (BA) (J44 code)

Details of installation of the module of management of BA (1 of 2)

And — the Cover of the luggage compartment with a vetrootboynik

In — the Basic arm of a vetrootboynik

Details of installation of the module of management of BA (2 of 2)

3 — Nuts
4 — BA electrical wiring Socket
A2/6 — a CD changer

A2/42 — the TV tuner
N62 — the Module of management of BA
X26/26 — I Will corrode BA electrical wiring

 PERFORMANCE ORDER

  1. Switch off ignition, activate the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — Grounding of the battery

  1. Having released six clamps (on three from each party), uncover equipped with a vetrootboynik (And) the luggage compartment.
  2. Remove a basic arm (V) of a vetrootboynik from the left wall of the luggage compartment.
  3. On models of the corresponding complete set (V53 code) remove the left ware box.
  4. On models of the corresponding complete set remove the TV tuner (A2/42), - the EM9 code and a CD changer (A2/6), - the EP5 code (see the Section Removal and installation of the CD changer/TV-tuner).
  5. Give fixing nuts (3), disunite sockets (X26/26 and 4) and remove the module of management of BA (N62).
  6. Installation is made upside-down.
  7. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Module of management of heating of seats (H11 code)

Details of installation of the module of management of heating of seats (H11 code)

1 — Fixing nuts
3 — the Socket

N25/6 — the Module of management

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Having released six clamps (on three from each party), uncover equipped with a vetrootboynik (And) the luggage compartment.
  4. Remove a basic arm (V) of a vetrootboynik from the left wall of the luggage compartment.
  5. On models of the corresponding complete set (V53 code) remove the left ware box.
  6. On models of the corresponding complete set remove the TV tuner (A2/42), - the EM9 code and a CD changer (A2/6), - the EP5 code (see the Section Removal and installation of the CD changer/TV-tuner).
  7. Give fixing nuts (1), disunite the socket (3) and remove the module of management (N25/6).
  8. Installation is made upside-down, - on models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  9. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine) and enter the required basic settings of the onboard equipment.

Module of management of system of voice commands of Linguatronic (EL1 ÷ EL6 codes)

Details of installation of the module of management of the Linguatronic system

1, 3 — Nuts
2 — the Basic arm
4 — the Panel of finishing of a foot well
5 — the Socket

6 — I Will corrode connections of the fiber-optical D2B cable
A35/11 — the Module of management Linguatronic

 PERFORMANCE ORDER

  1. Switch off ignition, activate the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — Grounding of the battery

  1. Unbend the carpet panel in a driver's foot well.
  2. In case of need raise the finishing panel (4) and release nuts (1).
  3. Remove the module of management of Linguatronic (A35/11) assembled with a basic arm (2).
  4. Release and disunite sockets (5 and 6), - at once muffle entrances of wave guides of the fiber-optical D2B cable special caps.
  5. Give fixing nuts (3) and remove the module of management (A35/11).
  6. Installation is made upside-down.
  7. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Module of management of the amplifier of the audio system (E66 code)

Details of installation of the module of management of the amplifier of the audio system

1 — the electrical wiring Socket
2 — Nuts
3 — the Console

4 — Screws
N40/9 — the Amplifier

 PERFORMANCE ORDER

  1. Shift the lifted driver's seat forward against the stop.
  1. Switch off ignition, activate the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — Grounding of the battery

  1. Disunite the socket (1).
  2. Give nuts (2) and remove the console (3) with the amplifier (N40/9) installed on it.
  3. Turn out fixing screws (4) and remove the amplifier (N40/9) from the console (3).
  4. Installation is made upside-down.
  5. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).

Module of management of SRS

Release models till 30.11.01

Details of installation of the module of management of SRS on release models till 30.11.01

N2/2 — the Module of management

W26 — Grounding of the module

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Remove the central console (see the Head Kuzov).
  3. Disconnect an electrical wiring from the module of management (N2/2), - try to remember the scheme of connection of the weight (W26)
  4. Turn out fixing screws and remove the module (N2/2).
  5. Installation is made upside-down, - marking in the form of an arrow on a casing of the installed module has to specify forward in the direction of travel.
  6. In conclusion make input of program data of SRS.

Release models from 01.12.01

Details of installation of the module of management of SRS (N2/2) on release models since 01.12.01.

 PERFORMANCE ORDER

  1. Remove the module of management of the device of protection against towage (see above).
  2. Disconnect an electrical wiring, release fixture and remove the module of management of SRS (N2/2), - try to remember the scheme of connection of the weight (W26).
  3. Installation is made upside-down.
  4. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).