dbba662c

12.3.20. Removal and installation of seatbacks

Front seats

Cabriolet models / short base

Details of installation of a back of a front seat (Cabriolet model / short base)

1 — the Cap
2 — the Screw
3 — the Finishing panel
4 — Screws of the connecting block
5 — the Electrical wiring
6 — the Binding
7 — Bolts of fastening of a back
8 — the Back
9 — the Pneumatic line
10 — the Operating valve

a, b, c — Sockets of an electrical wiring of the module of management
N32/1 — the Module of management of adjustment of a driver's seat / a steering column with memory of installations
N32/2 — the Module of management of adjustment of a passenger seat with memory of installations
X55/3 — the Socket of an electrical wiring of heating of a driver's seat
X55/4 — the Socket of an electrical wiring of heating of a passenger seat
Arrow — the Sealing cap

 PERFORMANCE ORDER

  1. Remove assembly of a front seat (see the Section Removal and installation of assemblies of front seats).
  2. Remove a cap (1) and turn out the screw (2) from the finishing panel (3).
  3. Take a sealing cap (shooter) and turn out the fixing screw located under it.
  4. Having wrung out back, release from clamps and remove the side finishing panel (3).
  5. Disunite the socket (a) of an electrical wiring of the module of management (N32/1 or N 32/2).
  6. Having marked adjusting provisions, disunite sockets (b and c) on a block (X55/3 or X55/4).
  7. Turn out screws (4) of the connecting block.
  8. On models of the corresponding complete set (SM7 and SM/8 code) remove the control valve (10) and disconnect the pneumatic line (9) of multicircuit adjustment.
  9. Take aside an electrical wiring (5) and (at the corresponding complete set) the pneumatic line, - banding bandages (6) are subject to replacement without fail.
  10. Turn out fixing bolts with left and on the right side and remove a back (8) of a seat.
  11. Installation is made upside-down, - track correctness of connection of an electrical wiring.

Station wagon models

Details of installation of a back of a front seat (Station wagon model)

1 — the Right finishing panel
2 — the Fixing bolt
3 — the Left finishing panel
4 — Screws of the connecting block
5 — the Electrical wiring
6 — the Binding
7 — Bolts of fastening of a back
8 — the Back
9 — the Pneumatic line
10 — the Operating valve

a, b, c — Sockets of an electrical wiring of the module of management
N32/1 — the Module of management of adjustment of a driver's seat / a steering column with memory of installations
N32/2 — the Module of management of adjustment of a passenger seat with memory of installations
X55/3 — the Socket of an electrical wiring of heating of a driver's seat
X55/4 — the Socket of an electrical wiring of heating of a passenger seat
Arrow — the electrical wiring Socket

 PERFORMANCE ORDER

  1. Remove assembly of a front seat (see the Section Removal and installation of assemblies of front seats).
  2. Remove a sealing cap, turn out the fixing screw (2) and remove the right finishing panel (1).
  3. The left finishing panel (3) is removed also as well as on the Cabriolet models (see paragraphs with 2 on 4).
  4. Disunite the socket (5) of an electrical wiring of the module of management (N32/1 or N 32/2).
  5. On models with heating of seats (H10 code) disunite sockets (X55/3 or X55/4) of the corresponding electrical wiring. Also release the socket specified by an arrow and release both wires of heating of a back (8) from its casing, previously having marked them.
  6. On models of the corresponding complete set (SM7 and SM/8 code) remove the control valve (10) and disconnect the pneumatic line (9) of multicircuit adjustment.
  7. Further act in the manner similar described above for the Cabriolet models (see above paragraphs with 9 on 11).

Back seats

Details of installation of a back of a back seat (1 of 2)

1 — the Finishing panel

2 — the back clamp otpuskaniye Lever

Details of installation of a back of a back seat (2 of 2)

3 — heating electrical wiring Sockets (R13/6x1, - at the left, or R13/8x1, - on the right)
4 — the Mechanism of blocking of a back
5 — the Lock washer of bolts of the lock

6 — back lock Bolts
7 — Screws of fastening of a back

 PERFORMANCE ORDER

  1. Remove back head restraints and put a seatback forward.
  2. Having hooked, remove the lever (2) otpuskaniye of a clamp of a back.
  3. Turn out fixing screws and remove the finishing panel (1).
  4. On models of the corresponding complete set (H11 code) disunite sockets (3) electrical wirings of heating of a back (R13/6x1 or R13/8x1), cut obvyazny bandages and release from a wire back.
  5. Remove a lock washer (5), turn out bolts (6) and disconnect the mechanism of blocking of a back.
  6. Turn out fixing bolts (7) and remove a back.
  7. Installation is made upside-down.