dbba662c

12.3.18. Removal and installation of assemblies of front seats

Cabriolet models / short base

Details of installation of a front seat on the Cabriolet models (1 of 2)

1 — Assembly of a front seat
2 — Forward bolts of fastening of a frame of a seat
3 — Bolts of fastening of an assembly bracket of the fire extinguisher
4 — the Pneumatic line
5 — Back bolts of fastening of a frame of a seat

6 — a seat regulator Emphasis
X55/15 — the Socket of an electrical wiring of a driver's seat
X55/16 — the Socket of an electrical wiring of a passenger seat

Details of installation of a front seat on the Cabriolet models (2 of 2)

And — the Cover of access to a jack
In — the Assembly bracket of fastening of a jack

With — Bolts
Shooters — Clamps

 PERFORMANCE ORDER

  1. Remove an emphasis (6) of the regulator of a seat.
  2. Shift assembly of a seat (1) forward and turn out back bolts (5) of fastening of a frame.
  3. Shift assembly of a seat (1) back.
  4. Release clamps (shooters) and uncover (And) domkratny office (only passenger seat).
  5. Take a jack, then turn out bolts (C) and remove an assembly bracket (V) of fastening of a jack (only passenger seat).
  6. Turn out forward bolts (2) fastenings of a frame of a seat.
  7. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  8. Disconnect a negative wire from the battery.
  9. Remove the fire extinguisher (only driver's seat).
  10. Turn out screws (3) fastenings of an assembly bracket of the fire extinguisher (only driver's seat).
  11. Incline a seat forward and disunite the socket (X55/15 or X55/16) of an electrical wiring.
  12. On models of the corresponding complete set (SM7 and SM/8 code) disconnect the pneumatic line (4) of multicircuit adjustment.
  13. Remove assembly of a front seat (1).
  14. Installation is made upside-down, - at installation of an emphasis (6) leave free not less than two teeths of an adjusting lath.
  15. On models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  16. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine), and also make sure of serviceability of functioning of the electric drive of a seat.

Station wagon models

Details of installation of a front seat on the Station wagon models

1 — Assembly of a seat
2 — the Cap
3 — the Bolt of anchor knot of a seat belt
4 — Back bolts of fastening of a frame of a seat
5 — Forward bolts of fastening of a frame of a seat
6 — the Pneumatic socket
7 — a regulator Emphasis

N32/1 — the Module of management of adjustment of a driver's seat / a steering column with memory of installations
N32/2 — the Module of management of adjustment of a passenger seat with memory of installations
X55/3 — the Socket of an electrical wiring of heating of a driver's seat
X55/4 — the Socket of an electrical wiring of heating of a passenger seat

 PERFORMANCE ORDER

  1. Shift assembly of a seat (1) in extreme back situation and remove an emphasis (7) of the regulator.
  2. Shift assembly of a seat forward.
  3. Dismantle a decorative cap (2) and turn out an anchor bolt (3) seat belts.
  4. Turn out back bolts (4) fastenings of a frame, then shift a seat (1) back and turn out forward bolts (5).
  5. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  6. Disconnect a negative wire from the battery.
  7. Disunite sockets of an electrical wiring of the drive (N32/1 or N32/2) and (on models of the corresponding complete set, - the H10 code) heating (X55/3 or X55/4) of a seat.
  8. On models of the corresponding complete set (SM7 and SM/8 code) disunite the pneumatic socket (6) of multicircuit adjustment.
  9. Remove assembly of a front seat (1).
  10. Installation is made upside-down, - at installation of an emphasis (6) leave free not less than two teeths of an adjusting lath.
  11. On models of the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  12. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine), and also make sure of serviceability of functioning of the electric drive of a seat.