dbba662c

12.3.14. Removal and installation of panels of finishing of body racks

Racks And

Details of installation of panels of finishing of racks And

1 — a doorway Sealant

2 — Finishing panels

 PERFORMANCE ORDER

  1. Release from a first line of a doorway a rubber sealant (1).
  2. Having pulled, release the finishing panel (2) on a sealant of a window frame.
  3. Installation is made upside-down.

Racks In

Cabriolet models

Details of installation of panels of finishing of racks In on the Cabriolet models

1 — the Finishing panel of a rack
2 — the Top side finishing panel
3 — the Directing bracket of the top anchor knot of a seat belt
4 — the Protector

5 — the Ceiling finishing panel
6 — the Covering from porous rubber
7 — the Socket of an alarm buzzer of the movement by a backing (BA)
Arrow — the Cutting cover

 PERFORMANCE ORDER

  1. Remove side panels of finishing of salon (see the Section Removal and installation of panels of finishing of salon).
  2. Release a rivet clamp of fastening of the finishing panel (1) in the basis of a rack of Century.
  3. Having turned out the fixing bolts located under a facing framework, remove the top handle.
  4. Having released the respective region of a door sealant, remove the top side finishing panel (2).
  5. Having released the nut located under a facing cover, remove the directing bracket (3) seat belts.
  6. Remove a protector (4) on both sides of the ceiling finishing panel (5).
  7. Remove the panel (5).
  8. On models of the corresponding complete set (J44 code) release a porous and rubber covering (6) and disunite the socket (7) of an electrical wiring of the ultrasonic sensor of the BA signaling device (only on the right rack).
  9. Release from a body aperture around a rack In a door sealant.
  10. Remove a protector (4) from the back party of a rack of Century.
  11. Having accurately released clamps, remove a cutting cover (shooter) and release from it a seat belt.
  12. Remove the panel (1) of finishing of a rack.
  13. Installation is made upside-down.

Station wagon models

Details of installation of panels of finishing of racks In on the Station wagon models (1 of 4)

1 — the Finishing panel

Details of installation of panels of finishing of racks In on the Station wagon models (2 of 4)

2 — the Cap

Details of installation of panels of finishing of racks In on the Station wagon models (3 of 4)

3 — the Anchor bolt

Details of installation of panels of finishing of racks In on the Station wagon models (4 of 4)

5 — the Nut of the directing bracket of the top anchor knot of a seat belt


 PERFORMANCE ORDER

  1. Remove door a sealant (arrow) on both sides of a rack of Century.
  2. Remove a cap (2) and turn out a bolt (3) of the lower anchor knot of a seat belt.
  3. Remove a facing cover (4) and give a nut (5) of fastening of the directing bracket of the top anchor knot of a seat belt.
  4. Release a seat belt from the panel (1) of finishing of a rack of Century.
  5. On models of the corresponding complete set (H11 code) disconnect an electrical wiring from the switch of heating of a back seat.
  6. Remove the panel (1) of finishing of a rack of Century.
  7. Installation is made upside-down.

Back racks (Station wagon models)

The corresponding illustrative material is presented on an illustration of the Detail of installation of a door of a back on the Station wagon models and сопр. illustrations to which all references which are found in the text belong.

Details of installation of the panel of finishing of the left back rack

1 — the Protector
2 — the Finishing panel
H4/7h2 — the Left back loudspeaker

H4/8h2 — the Right back loudspeaker

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (V53 and V57 codes) uncover the luggage compartment (And).
  2. On models of the corresponding complete set (V53 code) uncover (In) side a ware compartment, then turn out the fixing screw (D) and separate a ware compartment (C) from a back rack.
  3. Remove a protector (1) of edge of a doorway from a back rack.
  4. Having given aside, remove the finishing panel (2) racks, - do not forget disunite the loudspeaker electrical wiring socket (H4/7h2 or H4/8h2).
  5. On models of the corresponding complete set (J44 code) disunite the socket of an electrical wiring of the BA signaling device (only on the right rack).
  6. Remove the panel (2).
  7. Installation is made upside-down.