dbba662c

12.3.12. Removal and installation of the dashboard

Самоконтрящийся fixture is subject to replacement without fail!

Details of installation of the dashboard (1 of 12)

31 — EIS/EZS Safety lock
42 — the Safety lock of a combination of devices

F34 — the Assembly block of safety locks

Details of installation of the dashboard (2 of 12)

1 — Air ducts

Details of installation of the dashboard (3 of 12)

3 — the Plait of a console electrical wiring

Details of installation of the dashboard (4 of 12)

2 — the Block of alignment of potentials

Details of installation of the dashboard (5 of 12)

4 — the Connecting electrical wiring

5 — grounding/shielding Conclusions

Details of installation of the dashboard (6 of 12)

6 — the Central fixing screws

Details of installation of the dashboard (7 of 12)

7 — the Fixing screw

Details of installation of the dashboard (8 of 12)

8 — the Fixing bolt

Details of installation of the dashboard (9 of 12)

9 — the Fixing nut

Details of installation of the dashboard (10 of 12)

10 — the Fixing screw

Details of installation of the dashboard (11 of 12)

11 — the Assembly bracket
12 — the Regulator

13 — the Pin
14 — the Groove

Details of installation of the dashboard (12 of 12)

12 — the Regulator


 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate the service mode of system of an emergency call of TELE AID (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the left lower section of finishing of the dashboard (see the Section Removal and installation of the left lower section of finishing of the dashboard).
  4. Remove an electrodriving adjustable steering column (see the Head Podvesk and steering).
  5. Remove the left cover of the dashboard.
  6. Take safety locks of the electronic switch of the lock of ignition (EIS/EZS) (31) and a combination of devices (42) from the assembly block (F34).
  7. Remove modules of management of AT (ETC) and, - on models of the corresponding complete set (the ET code, except 463.246/249), - systems of an emergency call of TELE AID (see the Head Onboard electric equipment).
  8. Remove three air ducts of systems of heating/ventilation of air laid under the central console (1).
  9. Disunite sockets of connection of a console plait (3) with an electrical wiring of a driver's foot well, - try to remember adjusting provisions of sockets, as well as routes of laying of plaits.
  10. In a driver's foot well remove sockets from a block of alignment of potentials (2).
  11. Disconnect conclusions of grounding and shielding of the tire of data of CAN from a grounding point in the basis of the left rack And.
  12. Remove a forward ashtray (see the Section Removal and installation of a forward ashtray).
  13. Remove the facing panel of console section of the dashboard (see the Section Removal and installation of the facing panel of console section of the dashboard).
  14. Remove the loudspeaker which is built in in the central part of the dashboard (see the Head Onboard electric equipment).
  15. Remove the radio receiver (see the Head Onboard electric equipment).
  16. On models of the corresponding complete set (ET4 code) remove assembly of the multipurpose display / module of management of the COMAND system (see the Head Onboard electric equipment).
  17. Mark adjusting provisions of electric sockets in selections in the central part of the dashboard.
  18. Remove the right cover of the dashboard.
  19. Remove assembly of a ware box (see the Section Removal and installation of a ware box).
  20. Remove the right lower cover of the dashboard (see the Section Removal and installation of the lower covers of the dashboard).
  21. Disconnect an electrical wiring (4) from a block of alignment of potentials/distributor of the tire of data of CAN under a casing of the K/V evaporator, - try to remember routes of laying of plaits.
  22. Disconnect conclusions of grounding and shielding (5) from a grounding point, - again try to remember routes of laying of plaits.
  23. Turn out the central bolts (6) of fastening of assembly of the dashboard to a partition of a motive compartment.
  24. Turn out bolts (7) of fastening of the dashboard to the tunnel of the transmission line.
  25. Turn out bolts (8) of fastening of an arm of a shirt of a steering column in the top part of a partition of a motive compartment, - bolts are located under an assembly bracket of the dashboard.
  26. Give nuts (9) of fastening of an arm of a shirt of a steering column on a partition of a motive compartment in a driver's foot well, - in case of need block from rotation of a head of reciprocal bolts from the engine.
  27. Turn out screws (10) (three on the right and three at the left) fastenings of an assembly bracket (11) dashboards.
  28. Having given with turn up, remove the dashboard, in case of need use the help of the assistant.
  29. Installation is made upside-down, - at the corresponding complete set (ET2 code) deactivate the service mode of the TELE AID system (see the Section Activation/deactivation of the Service Mode of System of an Emergency Call of TELE AID).
  30. In conclusion make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see the Head Sistemy of electric equipment of the engine).