dbba662c

11.4.13. Removal and installation of the steering mechanism

Petrol models

The corresponding illustrative material is presented on the illustrations Scheme of the Organization of the Steering Drive and Illustration below to which all references which are found in the text belong.

Details of installation of the steering mechanism on petrol models

6 — the Steering bipod
8 — the Steering mechanism
15 — Hollow bolts of nipple connections

16 — the Bolt of fastening of a steering shaft
17 — Bolts of fastening of assembly of the steering mechanism

 PERFORMANCE ORDER

  1. By means of a suitable stripper to a vypressuyta cross draft (9) from a steering bipod (7).
  2. On the models equipped with engines of a series 113 remove the left block headlight (see the Head Onboard electric equipment) and the steering pump (see the Section Removal and installation of the steering pump).
  3. Remove a radiator (see the Head of the Cooling system, heating, ventilation and air conditioning).
  4. Remove the line (14) of cooling of GUR liquid (see the Section Removal and installation of the line of cooling of GUR liquid).
  5. Turn out hollow bolts (15) nipple connections and disconnect hydraulic lines from assembly of the steering mechanism, - merge hydraulic liquid in in advance prepared capacity.
  6. Turn out a bolt (16) and disconnect the lower cardan hinge of a steering shaft from an entrance shaft of the steering mechanism.
  7. Turn out fixing bolts (17) and remove assembly of the steering mechanism.
  8. Installation is made upside-down. Do not forget to check levels of working liquids and, in case of need to make the corresponding adjustments.
  9. In conclusion make cleaning of the processor memory of system of onboard self-diagnostics (see the Head Sistemy of electric equipment of the engine) and adjust the angles of installation of forward wheels (see the Part suspension bracket Geometry).

Diesel models

Model 463.323 (M612)

The corresponding illustrative material is presented on the illustrations Scheme of the Organization of the Steering Drive and Illustration below to which all references which are found in the text belong.

Preparation for removal of the steering pump (model 463.323)

13 — the Pressure head line
15 — the Left air duct
16 — the Right air duct
17 — the Belt of the drive of auxiliary units

18 — the Driving pulley
19 — the K/V Compressor
20 — the Fixing collar

 PERFORMANCE ORDER

  1. Remove panels of finishing of a cover of a head of cylinders.
  2. Remove the viscous coupling of the drive of the fan of the cooling system (see the Head of the Cooling system, heating, ventilation and air conditioning).
  3. Remove a cooling system radiator (see the Head of the Cooling system, heating, ventilation and air conditioning).
  4. Remove left (15) and the right (16) sleeves of inlet air ducts.
  5. Take off a belt of the drive of auxiliary units (see the Head Dvigatel).
  6. Remove a pulley (18) of the drive of the steering pump (11) (see the Section Removal and installation of the steering pump).
  7. Pump out liquid from the GUR tank.
  8. Remove the K/B (19) compressor and, without disconnecting refrigerator lines, take it aside.
  9. Remove the left forward wheel.
  10. Remove the left block headlight (see the Head Onboard electric equipment).
  11. By means of a suitable stripper to a vypressuyta cross draft (9) from a steering bipod (7).
  12. Having performed the procedures described in paragraphs with 5 on 7 for petrol engines remove assembly of the steering mechanism (8).
  13. Installation is made upside-down. In conclusion do not forget to make adjustment of angles of installation of forward wheels (see the Part suspension bracket Geometry).

Model 463.333 (M628)

The corresponding illustrative material is presented on illustrations of the Detail of installation of the steering pump (model with M628 engines) (1 of 2), Details of installation of the steering pump () (2 of 2) and illustrations are lower than model with M628 engines to which all references which are found in the text belong.

Location of a cover (22) in a wheel arch


 PERFORMANCE ORDER

  1. The car also establish to Poddomkratta it on props.
  2. Remove the left forward wheel.
  3. Remove a loker of protection of a wheel arch.
  4. Remove the left block headlight (see the Head Onboard electric equipment).
  5. Remove the air cleaner (1).
  6. Remove the left air inlet (2).
  7. Turn out four screws, take the measuring probe and turn off a cover of an oil-filling mouth, then remove the finishing panel (4).
  8. Remove a radiator (see the Head of the Cooling system, heating, ventilation and air conditioning).
  9. Remove a casing of an oil filter (20).
  10. Pump out liquid from the GUR (7) tank.
  11. Remove the tank (7) (see paragraphs 13 and 14 in the Section Removal and installation of the steering pump).
  12. Throw off a belt of the drive of auxiliary units (14) from a driving pulley (10) of pump assembly (11) (see paragraph 15 in the Section Removal and installation of the steering pump).
  13. Weaken fastening of an air duct (21) on a head of cylinders.
  14. Uncover (22) in a wheel arch.
  15. Remove the turbocompressor thermofilter.
  16. Remove the left lower air duct (17).
  17. By means of a suitable stripper to a vypressuyta cross draft from a steering bipod.
  18. Having performed the procedures described in paragraphs with 5 on 7 for petrol engines remove assembly of the steering mechanism (8).
  19. Installation is made upside-down. Do not forget to check levels of working liquids and, in case of need to make the corresponding adjustments.
  20. In conclusion make cleaning of the processor memory of system of onboard self-diagnostics (see the Head Sistemy of electric equipment of the engine) and adjust the angles of installation of forward wheels (see the Part suspension bracket Geometry).